1. In the engine compartment, share a kettle with the front wiper. In the engine compartment, a kettle is shared with the front wiper. When the front cover is opened, the glass water filling port has a unified logo. The position of the rear wiper plus glass water is the same as that of our front wiper plus glass water. They are connected by pipes.
2. Find the place where the pull wire is broken, and pull it down with a vise to open it.
3. This engine is matched with a 7-speed dual-clutch gearbox. The dual-clutch gearbox has fast gearshift speed and high transmission efficiency, which is very suitable for use with small-displement turbocharged engines.The front suspension of Metway adopts McPherson-type independent suspension, and the rear suspension adopts semi-longitudinal arm-type independent suspension.
4. The left side of the engine compartment. Metway is a multi-purpose VAN (bus, van) under Volkswagen. When you open the hood, you can see the fuse of the license plate light on the left side of the engine compartment, under the steering wheel and on the left side of the instrument.
5. The position of adding water to the glass of the car. The glass water of the car should be added to the glass water storage tank located in the engine compartment.
6. Steps to change the antifreeze in the water tank: open the lid and unswit the lid of the water tank. Turn on the open water switch and release the original water in the water tank at the bottom of the water tank. After the water is released, an appropriate amount of liquid sealant should be applied to it when the water switch is installed.
The car mainly finds the power switch of the hood. Generally, on the left panel of the driver's seat, it may be a power switch pulled by hand or foot. The owner can open the hood by pulling or stepping on the power switch with his hand. After the owner presses or steps on the power switch, the hood of the car will be lifted up, leaving a gap of about 3-5 centimeters.
Specific steps: (1) First open the door, sit in the driver's seat, and then find the engine switch handle on the left side of the driver's seat. ( 2) Pull the handle of the car engine with your hand and hear a bang. ( 3) Check whether the hood of the car is open. If there is an obvious gap, it means that the hood of the car has been opened.
How to turn on the hood: The hood switches of most cars on the market basically have the same handle as the button on the driver's side lower baffle. After slowly pulling the hood, it will make a sound immediately. Then, you can find the switch sticking out of the hood and turn on the hood.
Before the Honda Accord hood is opened, it needs to be unlocked in the car, and then the lever in the center of the engine compartment is unlocked for the second time to open the engine hatch. If the engine cover lock latch is difficult to move, or the engine cover can be opened without pulling the lock latch, it should be cleaned and moistened. Sliding latch mechanism.
The illustration of the front cover of the Accord is as follows: Tools: Honda Accord. Open the door on the driver's side of the Honda Accord. Pull the hood switch on the left side of the Honda Accord driver's leg. Lift the engine hood of the Honda Accord upwards.
In the position of the driver's left foot, there are two wrenches that control the hood and the trunk respectively; the buttons of the trunk and the fuel tank are integrated. Lifting up is to open the trunk, and pressing down is to open the fuel tank cover.
First, find the hood, which is located on the driver's side of the engine compartment. Second, find the four screw knees to be removed. Third, use a screwdriver to unscrew the screw knee. When all of them are removed, the hood can be successfully removed. Finally, slowly open the hood with a small handle to complete the whole opening process.
The Accord engine cover switch is in the cab, and the light switch is located below. You can open the engine cover by pulling the latch, and use the top pillar to hold the engine cover. The engine cover has the function of protecting the engine and the effect of soundproofing.
The specific operation steps are as follows: open the door on the driver's side of the Honda Accord. Pull the hood switch on the left side of the Honda Accord driver's leg. Lift the engine hood of the Honda Accord upwards.Pull the trunk switch of the Honda Accord door. Push up to open the trunk.
1. The switch of the hood of Land Rover is in the car, which needs to be turned on manually, and the position of the switch is around the foot pedal. There is a switch button on the left side of the pedal. We can press the switch to open the outer hood. Put the hydraulic cylinder of the hood into the groove of the hood to support it.
2. The engine hatch switch of Volkswagen Touareg is located in the lower left corner of the driver's seat. As shown in the figure below, we can lift the opening handle along the arrow, lift the engine cover and open it, then remove the engine hatch support rod from its fixed bracket, and finally hang the engine hatch support rod into the display. In the groove of the motor hatch.
3. The engine hatch switch of Volkswagen Touareg is located in the lower left corner of the driver's seat. As shown in the figure below, we can lift the handle along the arrow, lift the engine hood and open it, then remove the engine hatch support rod from its fixed bracket, and finally hang the engine hood support rod into In the groove of the engine cover.
Japan customs transaction analysis-APP, download it now, new users will receive a novice gift pack.
1. In the engine compartment, share a kettle with the front wiper. In the engine compartment, a kettle is shared with the front wiper. When the front cover is opened, the glass water filling port has a unified logo. The position of the rear wiper plus glass water is the same as that of our front wiper plus glass water. They are connected by pipes.
2. Find the place where the pull wire is broken, and pull it down with a vise to open it.
3. This engine is matched with a 7-speed dual-clutch gearbox. The dual-clutch gearbox has fast gearshift speed and high transmission efficiency, which is very suitable for use with small-displement turbocharged engines.The front suspension of Metway adopts McPherson-type independent suspension, and the rear suspension adopts semi-longitudinal arm-type independent suspension.
4. The left side of the engine compartment. Metway is a multi-purpose VAN (bus, van) under Volkswagen. When you open the hood, you can see the fuse of the license plate light on the left side of the engine compartment, under the steering wheel and on the left side of the instrument.
5. The position of adding water to the glass of the car. The glass water of the car should be added to the glass water storage tank located in the engine compartment.
6. Steps to change the antifreeze in the water tank: open the lid and unswit the lid of the water tank. Turn on the open water switch and release the original water in the water tank at the bottom of the water tank. After the water is released, an appropriate amount of liquid sealant should be applied to it when the water switch is installed.
The car mainly finds the power switch of the hood. Generally, on the left panel of the driver's seat, it may be a power switch pulled by hand or foot. The owner can open the hood by pulling or stepping on the power switch with his hand. After the owner presses or steps on the power switch, the hood of the car will be lifted up, leaving a gap of about 3-5 centimeters.
Specific steps: (1) First open the door, sit in the driver's seat, and then find the engine switch handle on the left side of the driver's seat. ( 2) Pull the handle of the car engine with your hand and hear a bang. ( 3) Check whether the hood of the car is open. If there is an obvious gap, it means that the hood of the car has been opened.
How to turn on the hood: The hood switches of most cars on the market basically have the same handle as the button on the driver's side lower baffle. After slowly pulling the hood, it will make a sound immediately. Then, you can find the switch sticking out of the hood and turn on the hood.
Before the Honda Accord hood is opened, it needs to be unlocked in the car, and then the lever in the center of the engine compartment is unlocked for the second time to open the engine hatch. If the engine cover lock latch is difficult to move, or the engine cover can be opened without pulling the lock latch, it should be cleaned and moistened. Sliding latch mechanism.
The illustration of the front cover of the Accord is as follows: Tools: Honda Accord. Open the door on the driver's side of the Honda Accord. Pull the hood switch on the left side of the Honda Accord driver's leg. Lift the engine hood of the Honda Accord upwards.
In the position of the driver's left foot, there are two wrenches that control the hood and the trunk respectively; the buttons of the trunk and the fuel tank are integrated. Lifting up is to open the trunk, and pressing down is to open the fuel tank cover.
First, find the hood, which is located on the driver's side of the engine compartment. Second, find the four screw knees to be removed. Third, use a screwdriver to unscrew the screw knee. When all of them are removed, the hood can be successfully removed. Finally, slowly open the hood with a small handle to complete the whole opening process.
The Accord engine cover switch is in the cab, and the light switch is located below. You can open the engine cover by pulling the latch, and use the top pillar to hold the engine cover. The engine cover has the function of protecting the engine and the effect of soundproofing.
The specific operation steps are as follows: open the door on the driver's side of the Honda Accord. Pull the hood switch on the left side of the Honda Accord driver's leg. Lift the engine hood of the Honda Accord upwards.Pull the trunk switch of the Honda Accord door. Push up to open the trunk.
1. The switch of the hood of Land Rover is in the car, which needs to be turned on manually, and the position of the switch is around the foot pedal. There is a switch button on the left side of the pedal. We can press the switch to open the outer hood. Put the hydraulic cylinder of the hood into the groove of the hood to support it.
2. The engine hatch switch of Volkswagen Touareg is located in the lower left corner of the driver's seat. As shown in the figure below, we can lift the opening handle along the arrow, lift the engine cover and open it, then remove the engine hatch support rod from its fixed bracket, and finally hang the engine hatch support rod into the display. In the groove of the motor hatch.
3. The engine hatch switch of Volkswagen Touareg is located in the lower left corner of the driver's seat. As shown in the figure below, we can lift the handle along the arrow, lift the engine hood and open it, then remove the engine hatch support rod from its fixed bracket, and finally hang the engine hood support rod into In the groove of the engine cover.
Trade data-driven supply chain optimization
author: 2024-12-24 01:12Sawmill products HS code references
author: 2024-12-24 00:55Global trade data integration services
author: 2024-12-24 00:05Supply chain optimization with trade data
author: 2024-12-24 00:00Pharmaceutical raw materials HS code checks
author: 2024-12-23 23:37Chemical industry HS code search
author: 2024-12-24 00:40Global trade data for currency hedging
author: 2024-12-24 00:35Refined sugar HS code identification
author: 2024-12-24 00:15Shipping lane performance metrics
author: 2024-12-24 00:02Trade data-driven policy analysis
author: 2024-12-23 23:28791.58MB
Check394.63MB
Check688.85MB
Check724.95MB
Check661.65MB
Check498.77MB
Check244.17MB
Check734.58MB
Check559.21MB
Check111.85MB
Check267.19MB
Check628.51MB
Check256.17MB
Check271.17MB
Check491.11MB
Check174.37MB
Check341.62MB
Check862.99MB
Check875.63MB
Check858.59MB
Check775.23MB
Check756.41MB
Check984.89MB
Check914.41MB
Check855.55MB
Check273.71MB
Check631.31MB
Check913.74MB
Check343.23MB
Check853.49MB
Check626.62MB
Check255.82MB
Check364.91MB
Check742.87MB
Check936.42MB
Check651.85MB
CheckScan to install
Japan customs transaction analysis to discover more
Netizen comments More
1497 Importer data
2024-12-24 01:02 recommend
1449 How to use trade data for market expansion
2024-12-24 00:21 recommend
370 HS code-based inventory forecasting
2024-12-23 23:43 recommend
739 HVAC equipment HS code mapping
2024-12-23 23:37 recommend
1152 How to ensure tariff compliance
2024-12-23 23:36 recommend