1. If the width is too large, there will be no accident during overtaking or if the road marking is narrower than the width of the car, the state stipulates that the car The total width of the vehicle shall not exceed 5m to meet the needs of the use of relevant public roads.
2. However, as long as it meets the national standard "Dimensions, Axle Weight and Mass Limits of Road Vehicles" (GB1589-2004), they are all standard sizes.Measurement method of car size: length and number of times; width × height. As the name implies, the so-called length, width and height are the external dimensions of the car, usually in millimeters (mm).
3. Width is the distance between the most prominent points of the outer sheet metal of the body. The length data of a car is the distance from the front of the front to the end of the rear of the car. The width is the distance between the most prominent points of the outer sheet metal of the car body. Generally, the front wheel eyebrow position of the car is the widest, and the general reflector is not included in the width of the body.
4. According to the common rules in the industry, the width of the body does not include the width of the left and right rearview mirrors, that is, the width after the rearview mirror is folded. The height of the car body is defined as: the distance from the ground to the highest point of the car. The so-called highest point is the highest position on the top of the body, but does not include the length of the roof antenna.
5. Vehicle width: Vehicle width is the distance between the two planes parallel to the longitudinal symmetrical plane of the vehicle and facing the fixed protruding parts on both sides of the vehicle. The automatic measuring instrument of vehicle outline size should comply with the measurement regulations, and the maximum allowable error of the measuring instrument: 1% or 20mm.
6. The body size is the data of the length, width and height of the car, indicating the external size of the car body. Body length × width × height measurement standard: body length refers to the distance from the most prominent position at the front of the car to the most prominent position at the rear of the car.
Benchmarks In actual measurement work, the plane of the body corrector is generally taken as the height reference plane.
In the body knotIn structural maintenance, when measuring the body structure data with the body measurement system, there are three important dimensional reference benchmarks: reference surface, central surface and zero plane.
Therefore, the use of steel tape measure and gauge can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and production year should be correctly selected. Parameter comparison When selecting the measurement reference point, the following principles should usually be followed. 1 Confirm that the measurement reference point is not deformed.
The body width is defined as the distance between the two extreme points in the direction of the width of the car, that is, the distance between the most prominent positions on the left and right of the car body. According to the general rules of the industry, the body width does not include the extension width of the left and right rearview mirrors, that is, the width of the folding rearview mirrors. The body height is defined as the distance from the ground to the highest point of the car.
The quality of the whole vehicle equipment (kg): the quality of the car is fully equipped, including the quality of all equipment such as lubricating oil, fuel, accompanying tools, spare tires, etc. Maximum total mass (kg): the total mass when the car is fully loaded. Maximum loading mass (kg): the maximum loading mass when the car is driving on the road.
Therefore, the use of steel tape measure and gauge ruler can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and year of production should be correctly selected. ( 2) Parameter comparison: When comparing parameters, the following principles should generally be followed: ensure that the measurement reference point is not deformed.
1. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
2. You need a tape measure or laser rangefinder. If you choose to use a tape measure, make sure it is accurate and long enough to measure the length of the entire body. If you choose to use a laser rangefinder, follow the instructions to make sure that it has been calibrated and ready for use.
3. In order to accurately obtain the body data, the three steps are the measurement of the size, the measurement of the upper body size, and the measurement of the front size of the body. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. Measurement of the overall deformation of the car body: Body shaping positioning detection is to use the measurement system provided by the straightening system to measure the coordinate parameters of each measurement point on the body, and compare the measurement data with the standard data of the model to check the straightening quality.
5. Stop the car after driving 10km on the road with poor road conditions, and touch the shock absorber shell with your hand. If it is not hot enough, it means that there is no resistance inside the shock absorber and the shock absorber does not work.
The front bundle ruler can be used to check and measure the front bundle. The tested vehicle must ensure that the tire pressure, the wheel is not in the center, the steering mechanism and the wheel bearing adjustment are in good condition, and the front wheel must be in the center and straight. When measuring with a front ruler, park the car on a flat, dry and clean ground.
Measurement method of automobile front bundle: First of all, the measurement method of automobile wheel bearing clearance is adjusted, and the tire inflation pressure conforms to the regulations.
The adjustment and measurement of the front beam of the car are as follows: the front beam of the front wheel is to make the distance between the front end of the two front wheels of the car smaller than the distance of the rear end.The difference in distance is called the front beam value. Looking down from the top of the car, the left and right front wheels form an "eight" shape with an opening to the back; the front bundle of the front wheel can be adjusted by changing the length of the crossbar.
Checking the front bundle value is generally carried out on a special front wheel locator. The front beam measurement method is first of all to adjust the gap of the automobile wheel hub bearing, and the tire inflation pressure conforms to the regulations. Park the car on the horizontal road and drive in a straight line.
Therefore, when the current bundle value is inappropriate, it needs to be adjusted and measured. To measure the front beam of a car, it is generally necessary to use a special front wheel locator, and generally there is no such professional instrument for self-measurement, and it can only be measured through simple tools. Of course, there is a certain error in the front beam of the car measured in this way.
1. Car size detection is as follows: the body length is defined as the distance between the two extreme points of the car, that is, the distance between the two points from the most prominent position of the front bumper of the car to the most prominent position of the rear bumper.
2. Body size: First, we will measure the size of each part of the car body, including the length, width and height. These data are crucial to the design, manufacture and safety of vehicles. For example, if the body width exceeds the specified limit, the vehicle may not be able to drive on certain roads.
3. Measurement of size: In the body structure, most of the control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. When the freight vehicle passes through the off-site law enforcement monitoring point normally at a running speed range of 0.5-100km/h, the Shenbang outline size measurement ADM system can automatically complete the identification and measurement of the length, width and height profile size and wheelbase of the freight vehicle, and output the correct measurement results to Off-site law enforcement edge management server.
International trade compliance dictionary-APP, download it now, new users will receive a novice gift pack.
1. If the width is too large, there will be no accident during overtaking or if the road marking is narrower than the width of the car, the state stipulates that the car The total width of the vehicle shall not exceed 5m to meet the needs of the use of relevant public roads.
2. However, as long as it meets the national standard "Dimensions, Axle Weight and Mass Limits of Road Vehicles" (GB1589-2004), they are all standard sizes.Measurement method of car size: length and number of times; width × height. As the name implies, the so-called length, width and height are the external dimensions of the car, usually in millimeters (mm).
3. Width is the distance between the most prominent points of the outer sheet metal of the body. The length data of a car is the distance from the front of the front to the end of the rear of the car. The width is the distance between the most prominent points of the outer sheet metal of the car body. Generally, the front wheel eyebrow position of the car is the widest, and the general reflector is not included in the width of the body.
4. According to the common rules in the industry, the width of the body does not include the width of the left and right rearview mirrors, that is, the width after the rearview mirror is folded. The height of the car body is defined as: the distance from the ground to the highest point of the car. The so-called highest point is the highest position on the top of the body, but does not include the length of the roof antenna.
5. Vehicle width: Vehicle width is the distance between the two planes parallel to the longitudinal symmetrical plane of the vehicle and facing the fixed protruding parts on both sides of the vehicle. The automatic measuring instrument of vehicle outline size should comply with the measurement regulations, and the maximum allowable error of the measuring instrument: 1% or 20mm.
6. The body size is the data of the length, width and height of the car, indicating the external size of the car body. Body length × width × height measurement standard: body length refers to the distance from the most prominent position at the front of the car to the most prominent position at the rear of the car.
Benchmarks In actual measurement work, the plane of the body corrector is generally taken as the height reference plane.
In the body knotIn structural maintenance, when measuring the body structure data with the body measurement system, there are three important dimensional reference benchmarks: reference surface, central surface and zero plane.
Therefore, the use of steel tape measure and gauge can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and production year should be correctly selected. Parameter comparison When selecting the measurement reference point, the following principles should usually be followed. 1 Confirm that the measurement reference point is not deformed.
The body width is defined as the distance between the two extreme points in the direction of the width of the car, that is, the distance between the most prominent positions on the left and right of the car body. According to the general rules of the industry, the body width does not include the extension width of the left and right rearview mirrors, that is, the width of the folding rearview mirrors. The body height is defined as the distance from the ground to the highest point of the car.
The quality of the whole vehicle equipment (kg): the quality of the car is fully equipped, including the quality of all equipment such as lubricating oil, fuel, accompanying tools, spare tires, etc. Maximum total mass (kg): the total mass when the car is fully loaded. Maximum loading mass (kg): the maximum loading mass when the car is driving on the road.
Therefore, the use of steel tape measure and gauge ruler can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and year of production should be correctly selected. ( 2) Parameter comparison: When comparing parameters, the following principles should generally be followed: ensure that the measurement reference point is not deformed.
1. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
2. You need a tape measure or laser rangefinder. If you choose to use a tape measure, make sure it is accurate and long enough to measure the length of the entire body. If you choose to use a laser rangefinder, follow the instructions to make sure that it has been calibrated and ready for use.
3. In order to accurately obtain the body data, the three steps are the measurement of the size, the measurement of the upper body size, and the measurement of the front size of the body. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. Measurement of the overall deformation of the car body: Body shaping positioning detection is to use the measurement system provided by the straightening system to measure the coordinate parameters of each measurement point on the body, and compare the measurement data with the standard data of the model to check the straightening quality.
5. Stop the car after driving 10km on the road with poor road conditions, and touch the shock absorber shell with your hand. If it is not hot enough, it means that there is no resistance inside the shock absorber and the shock absorber does not work.
The front bundle ruler can be used to check and measure the front bundle. The tested vehicle must ensure that the tire pressure, the wheel is not in the center, the steering mechanism and the wheel bearing adjustment are in good condition, and the front wheel must be in the center and straight. When measuring with a front ruler, park the car on a flat, dry and clean ground.
Measurement method of automobile front bundle: First of all, the measurement method of automobile wheel bearing clearance is adjusted, and the tire inflation pressure conforms to the regulations.
The adjustment and measurement of the front beam of the car are as follows: the front beam of the front wheel is to make the distance between the front end of the two front wheels of the car smaller than the distance of the rear end.The difference in distance is called the front beam value. Looking down from the top of the car, the left and right front wheels form an "eight" shape with an opening to the back; the front bundle of the front wheel can be adjusted by changing the length of the crossbar.
Checking the front bundle value is generally carried out on a special front wheel locator. The front beam measurement method is first of all to adjust the gap of the automobile wheel hub bearing, and the tire inflation pressure conforms to the regulations. Park the car on the horizontal road and drive in a straight line.
Therefore, when the current bundle value is inappropriate, it needs to be adjusted and measured. To measure the front beam of a car, it is generally necessary to use a special front wheel locator, and generally there is no such professional instrument for self-measurement, and it can only be measured through simple tools. Of course, there is a certain error in the front beam of the car measured in this way.
1. Car size detection is as follows: the body length is defined as the distance between the two extreme points of the car, that is, the distance between the two points from the most prominent position of the front bumper of the car to the most prominent position of the rear bumper.
2. Body size: First, we will measure the size of each part of the car body, including the length, width and height. These data are crucial to the design, manufacture and safety of vehicles. For example, if the body width exceeds the specified limit, the vehicle may not be able to drive on certain roads.
3. Measurement of size: In the body structure, most of the control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. When the freight vehicle passes through the off-site law enforcement monitoring point normally at a running speed range of 0.5-100km/h, the Shenbang outline size measurement ADM system can automatically complete the identification and measurement of the length, width and height profile size and wheelbase of the freight vehicle, and output the correct measurement results to Off-site law enforcement edge management server.
How to secure competitive freight rates
author: 2024-12-24 03:32Australia import export data visualization
author: 2024-12-24 03:01Holistic international trade reports
author: 2024-12-24 02:24HS code analytics for niche markets
author: 2024-12-24 01:24How to detect trade-based money laundering
author: 2024-12-24 01:12Global HS code standardization efforts
author: 2024-12-24 03:33High-precision instruments HS code mapping
author: 2024-12-24 03:13HS code-based supplier development
author: 2024-12-24 03:02HS code-based customs broker RFPs
author: 2024-12-24 02:23End-to-end shipment management
author: 2024-12-24 01:34
How to select the best trade data provider
647.98MB
Check
How to track compliance breaches
671.36MB
Check
HS code-based supply chain digitization
446.55MB
Check
HS code mapping tools for manufacturers
689.56MB
Check
API integration with HS code databases
261.43MB
Check
Latin American HS code alignment
399.76MB
Check
Cost-benefit analysis of export markets
784.97MB
Check
Africa import data trends
387.84MB
Check
Locating specialized suppliers by HS code
985.48MB
Check
HS code correlation with duty rates
138.45MB
Check
global trade management
619.42MB
Check
How to align trade data with ESG goals
247.82MB
Check
Agritech products HS code classification
476.98MB
Check
HS code analytics for port efficiency
634.27MB
Check
HS code harmonization in NAFTA region
244.99MB
Check
How to reduce documentation errors
612.62MB
Check
HS code-based global benchmarking
854.73MB
Check
Global trade data for PESTEL analysis
851.26MB
Check
Trade finance data solutions
352.11MB
Check
Real-time embargo monitoring
251.89MB
Check
Dairy sector HS code forecasting
596.35MB
Check
HS code-driven customs risk scoring
274.96MB
Check
Heavy machinery parts HS code verification
756.74MB
Check
How to simplify multi-leg shipments
586.14MB
Check
Asia import data insights
718.43MB
Check
Global trade duty recovery strategies
259.83MB
Check
European Union trade analytics
729.36MB
Check
Trade data integration with CRM
793.65MB
Check
How to implement JIT with global data
336.14MB
Check
HS code-driven market penetration analysis
162.84MB
Check
Global HS code classification standards
467.22MB
Check
Predictive analytics for supplier risks
625.17MB
Check
Advanced shipment analytics software
984.48MB
Check
Real-time shipment data alerts
636.19MB
Check
How to track shipment delays
528.84MB
Check
HS code-driven customs clearance SLAs
837.82MB
Check
Scan to install
International trade compliance dictionary to discover more
Netizen comments More
1463 Trade intelligence for emerging markets
2024-12-24 03:02 recommend
266 Data-driven customs paperwork reduction
2024-12-24 02:48 recommend
1447 Global trade event monitoring
2024-12-24 02:17 recommend
1353 Trade data-driven investment strategies
2024-12-24 02:17 recommend
2050 Supply chain sustainability metrics
2024-12-24 01:34 recommend