Real-time customs inspection logs

List of contents of this article:

• 1,Real-time customs inspection logs How to release water in the car water tank
• 2、 How to release the water in the car engine?
• 5, Car water tank How to release water

How to release water in the car water tank

How to release water in the car water tank: unswen the open water valve and remove the drain pipe of the water tank.Generally, the water tank of Japanese cars has a drain valve, and you only need to open the water valve. German cars generally need to remove the water tank drain pipe to release water. Turn on the hood switch under the cab. Open the hood, and the water tank is on the right.

The steps to add water to the car water tank are as follows: tighten the water tank cover, open the water tank drain valve, and release the antifreeze. Insert the rubber pipe connected to the tap water pipe into the inlet of the water tank, turn on the tap water, and keep the tap water flowing through the engine cooling system.

Turn on the switch of the hood under the cab. Open the hood, and the water tank is on the right. When opening the hood, you need to push the hood inward. Open the lid of the water tank and add water to the right amount. Note that the water added must be clean. Cover the water tank and close the hood.

Weizhi Automobile Water Tank Release Method

Weizhi Water Tank is located on the left side of the engine. The exhaust method of the fuel tank is carried out after replacing the coolant. The specific operation is as follows: lower the water tank and cover it, remove the water tank water pipe, and release the coolant. Insert the rubber pipe connected to the water pipe into the water inlet of the water tank, turn on the tap, and let the tap water flow continuously through the engine cooling system.

Tring off the water tank cover, open the water tank release valve, and release the antifreeze. Insert a rubber pipe connected to the tap water pipe into the water inlet of the water tank, turn on the tap, and let the tap water flow continuously through the engine cooling system.

Car water tank drainage steps: turn on the hood switch under the cab; turn on the hood. Note that when opening the hood, you need to push the hood lock inward;Open the water tank cover and drain the water to the right position; cover the water tank cover and close the engine hood.

Turn on the switch of the hood under the cab. Open the hood, and the water tank is on the right. When opening the hood, you need to push the hood inward. Open the lid of the water tank and add water to the right amount. Note that the water added must be clean. Cover the water tank and close the hood.

Method 1: Water inlet adding water method The water inlet of the car water tank is usually located in the front of the hood. There will be a sign on the water inlet cover, and the water inlet is usually written on the water inlet. To use this method, just open the lid of the water inlet and pour water into the water inlet. It should be noted that when adding water, pour it slowly to avoid splashing out.

, open the lid and release the original water in the water tank.2. There is a water release switch under the water tank. Some models also need to put water in the cylinder, and there is a water release screw on the cylinder. 3. There is a waterproof switch under the water tank. After draining the water, unstighten it and add antifreeze.

Do cars use water in winter

1. In winter, we should add special winter coolants to cars, without It's water.Because the freezing point of the coolant is lower than that of water and the boiling point is higher than that of water, that is to say, when the ambient temperature is low, the water will freeze, but the coolant will not.

2. Special antifreeze should be added to the car in winter, not water. Because the freezing point of antifreeze is lower than that of water and the boiling point is higher than that of water, that is to say, when the ambient temperature is low, the water will freeze, but the antifreeze will not.

3. Therefore, when the car is parked outside for a long time, the driver must drain the water in the water tank.

4. Thoroughly drain the water in the car. In winter, it is more taboo not to put the water in the car cooling system, which will cause damage to the car engine in the cold winter, especially at night. Therefore, it is recommended that drivers pay attention to the water release of the car in winter.

5. Water should be released, otherwise the engine will freeze.Add antifreeze, add it well. It's okay to add alcohol, add 3-4 bottles, but check the water tank frequently.

How to release the water in the car engine?

1. The water inside the car engine only needs to disconnect the return water pipe connected to the water tank and the engine, and it can be completely released, because the return water pipe is the lowest water level position of the engine. The specific operation steps for releasing water from the engine are as follows: turn off the engine and reduce the water temperature to normal temperature. Open the driver's side door.

2. After removing the engine assembly, you will find a water pipe below. Remove it. Because there is water in the water pipe, the antifreeze will gust out after removing the drain pipe. Please be careful not to burn it. Then when the water flows out, you can clearly see the thermoster directly, which means that all the water in the tank has been released.

3. We can use the oil dipstick to know the status of the oil. If the oil dipped in the oil dipped in the oil dip shows milky white, it can basically be confirmed that the lubrication system is water, which requires a thorough replacement of the oil filter. If possible, you can also use products specialized in cleaning the engine lubrication system for cleaning.

4. A water-blocking grid plate is designed at the rear of the engine compartment, and then a drainage hole is designed on the partition. The drain of the engine compartment is the most easily blocked, and it is also the most easily ignored by the owner. Because it is relatively close to the air outlet of the air conditioner.

5. Open the water tank cover, remove the sewer pipe, and then block the lower mouth of the water tank with the air pump to blow the water tank cover. In this way, it is more thorough, and the antifreeze in the engine can be released.

6. In addition, pay attention to the inspection and cleaning of the radiator and intake duct to ensure that the radiator is not adhered by debris and the intake duct is unobstructed. There is also some sporadic daily maintenance, observe whether the exposed rubber pipes and wires in the engine compartment have aging, cracking or glue opening, and check the car engine. Whether the screws of the parts in the cabin are loose, etc.

How to release water in the car water tank

, open the cover and release the original water in the tank. 2. There is a water release switch under the water tank. Some models also need to put water in the cylinder, and there is a water release screw on the cylinder. 3. There is a waterproof switch under the water tank. After draining the water, unstighten it and add antifreeze.

Turn on the switch of the hood under the cab. Open the hood, and the water tank is on the right.When opening the hood, you need to push the hood inward. Open the lid of the water tank and add water to the right amount. Note that the water added must be clean. Cover the water tank and close the hood.

There are special water release screws in the car water tank, which are generally in the lower left or lower right corner of the water tank. The material is generally plastic and relatively fragile. Just unscrew it by hand. After emptying, pay special attention not to tighten it too much when unstightening, which will be easy to break.

Loosen the water screw can release water. The water outlet of the Buick Enclave water tank is at the bottom of the water tank, and the water can be released by opening the water screw. The water tank is in the front compartment of the engine. It is marked on the water tank that it is forbidden to open the kettle lid when the engine is high. Ordinary water (tap water, mineral water) should not be added to the car tank.