How to reduce compliance-related delays

The car's (sticky) cylinder is caused by lack of water and high temperature, poor heat dissipation and high temperature, poor coordination of the cylinder liner, piston and piston ring or quality problems. After sticking the cylinder, the engine cannot turn and cannot be ignited.

3. The sticky cylinder of the motorcycle can start and catch fire, and you can consider replacing the cylinder. Motorcycle adhesive cylinder refers to the smaller gap between the piston and the cylinder block, resulting in the piston being stuck or not moving smoothly. Although the sticky cylinder will affect the performance and combustion efficiency of the motorcycle, it can still start and catch fire. If you encounter a sticky cylinder of the motorcycle, you can consider replacing the cylinder block.

4. If it can be started, there is no sticky cylinder. Maybe the piston is swollen to death, and when the engine cools down, it will be loosened. As long as it can be started normally, there is no problem.

5. The sticky cylinder of the pedal motorcycle engine will cause the cylinder, piston ring, piston and crankshaft are seriously worn or damaged after high temperature, causing the engine to die and cannot start.

6. No, the engine is stuck to the cylinder, and the piston can't move up and down in the cylinder, that is to say, the crankshaft can't rotate, and the vehicle will definitely not be able to get on the car. I hope to help you.

How to judge whether the engine is stuck to the cylinder! For example, there is any abnormality in starting the engine

1, there is a decrease in speed, weak operation, dull sound, super high water temperature, and the indication of the water temperature meter exceeds 100℃. At this time, sprinkle some water on the machine parts, and it will evaporate quickly. The main reason is the severe shortage of water and the failure of the water cooling system. If the engine is turned off immediately, a sticky cylinder may occur.

2. The motorcycle has a slight sticky cylinder. The fault phenomenon is generally that the noise is obviously louder, the power performance is worse, the engine temperature is likely to be higher, and there may be difficulty in starting, unstable idling and other phenomena.

3, 2) Whether the cylinder pad or cylinder head pad is cracked or leaking; (3) Whether the cylinder is seriously pulled, whether the piston ring is broken or stuck in the groove; (4) Whether the spark plug has a copper washer, and whether the spark plug is tightened. Check the tightness of the crankcase.

4. Simple discrimination of the general appearance of the cylinder: under normal circumstances, the power of the vehicle decreases significantly (commonly known as the powerless car). The water temperature is abnormal (the water temperature of the vehicle is started for a while, and the water temperature is even boiling). The lower exhaust gas increases, and there is blue smoke in the rear exhaust.

After the motorcycle glued the cylinder, the piston, piston ring and cylinder were replaced. After replacing these things, the properties of the car can still...

1. As soon as the existing adhesive cylinder is cut, the motorcycle in circulation gear should be quickly hung in idle gear, so that the vehicle can slide in idle gear. The motorcycle with manual clutch should immediately clutch the clutch, so that the huge resistance after the engine sticks to the cylinder can be at the clutch. Dissolve, so as not to cause the rear wheel to be locked.

2. There is no problem to run 80,000 kilometers after changing the cylinder. The connecting rod piston, bearings, etc. need to be replaced. It's a little expensive! The overall replacement of the engine is only 1,050 yuan. There is no problem to run 100,000 kilometers after replacement.

3. If the Yamaha 125 motorcycle wants to press out the original cylinder liner and then press down a new cylinder liner, there are few people who repair the car like this now, and they all directly replace the new cylinder block.

What is the cause of the engine pistonization of the contamination of the cylinder

1. The gap between the piston and the cylinder is too small x0dx0a In the process of friction between the piston and the cylinder, because the gap between the piston and the cylinder is too Small, resulting in the lack of oil film on the surface to form dry friction, resulting in sticky cylinders. When replacing the cylinder liner and piston, you should choose the piston and cylinder liner of the same group number.

2. If the engine oil is gone or the pressure is too low to the cylinder, resulting in an increase in the friction between the piston ring and the cylinder wall. The increase in friction will lead to severe heat. When the temperature reaches a certain value, it will burn the piston ring, damage the cylinder wall, and produce a sticky cylinder.

3. The main reason: the vehicle engine is stuck to the cylinder, mainly becauseThe engine cooling system seriously lacks coolant, causing the engine to have a high temperature. After that, the engine cylinder is glued together with the piston. If the engine is turned off immediately, it may produce a sticky cylinder.

4. The sticky cylinder of the motorcycle is mostly caused by the poor oil, or the lack of oil in the engine, and the failure of the oil pump caused by the failure of the oil pump, as well as the blockage of the oil filter element, oil filter or oil channel, which causes the poor oil supply.

What is the reason for the sticky cylinder of the engine?

The gap between the piston and the cylinder is too small x0dx0a In the process of friction between the piston and the cylinder, because the gap between the piston and the cylinder is too small, there is a lack of oil film on the surface to form dry friction, resulting in a sticky cylinder. When replacing the cylinder liner and piston, you should choose the piston and cylinder liner of the same group number.

Engine sticky cylinder refers to: the oil is gone or the pressure is too low to the cylinder, resulting in an increase in the friction between the piston ring and the cylinder wall. The increase in friction will lead to severe heating. When the temperature reaches a certain value, it will burn the piston ring, damage the cylinder wall, and produce a sticky cylinder.

The gap between the piston and the cylinder is too small. In the process of friction between the piston and the cylinder, because the gap between the piston and the cylinder is too small, the surface lacks oil film to form dry friction, resulting in sticky cylinder. When replacing the cylinder liner and piston, you should choose the piston and cylinder liner of the same group number.

The main reason: the cylinder of the vehicle engine is sticky, mainly due to the serious lack of coolant in the engine cooling system, resulting in the high temperature of the engine. After that, the engine cylinder is pasted together with the piston. If the engine is immediately turned off and stopped, the cylinder may be sticky.

The sticky cylinder is caused by the high water temperature. Is the cylinder liner you changed wet or dry? If it is wet, you must pay attention to the sealant on the cylinder liner during installation. When installing, rub some oil on the sealant, so that the sealant will not be damaged or dropped during installation.

List of contents of this article:

• 1,How to reduce compliance-related delays Is it easy to stick to the cylinder
• 2. Can the engine cylinder still start?
• 3, How to judge whether the engine is stuck to the cylinder! For example, there is any abnormality in starting the engine
• 4, After the motorcycle glued the cylinder, the piston, piston ring and cylinder were replaced. After replacing these things, the properties of the car can still...
• 5, What is the cause of the engine pistonization of the cylinder
• 6、 What is the reason for the sticky cylinder of the engine?

Is it easy for the car engine to stick to the cylinder

1. The main reason: The vehicle engine sticks to the cylinder, mainly due to the serious lack of coolant in the engine cooling system, causing the high temperature of the engine, and then the engine cylinder The cylinder is pasted together with the piston. If the engine is turned off immediately, a sticky cylinder may be generated.

2. The gap between the piston and the cylinder is too small x0dx0a In the process of friction between the piston and the cylinder, because the gap between the piston and the cylinder is too small, the surface lacks an oil film to form dry friction, resulting in sticky cylinder.When replacing the cylinder liner and piston, you should choose the piston and cylinder liner of the same group number.

3. This fault is relatively rare, because you didn't use the engine to work. Phenomenon. And run-in. Oil pressure. Water temperature description. I can only judge from my experience to see if it is helpful to you.

4. Note 1: Do not maintain high speed for a long time. If the high speed is maintained for a long time, the engine will stick to the cylinder, commonly known as pulling the cylinder. That is, the inside of the engine is too hot to melt the steel, resulting in adhesion. Just like the 86 in the "initial D" Note 2: The co-pilot should take the wet wipes and buy some coffee or Red Bull.

5. Caused by high temperature, frequent checking of engine oil, circulating water and air filter can prevent it.

Can the engine cylinder still start?

1. The engine sticky cylinder cannot be started. The following are the details about the engine adhesive cylinder: Reason: The gap between the piston and the cylinder is too small. In the process of friction between the piston and the cylinder, due to the small gap between the piston and the cylinder, the surface lacks an oil film to form friction, thus sticking the cylinder.

2、

Contact Us
Phone：020-83484615