1. When the engine inhales the fuel steam and air mixture and enters the compression link, the spark plug will automatically explode before ignition, resulting in cylinder vibration, which is the explosion. This phenomenon is particularly common because fuel contains low-flammable substances.
2. It is usually piezoelectric ceramics. When the engine vibrates, the ceramics inside are squeezed to produce electrical signals. Because this electrical signal is very weak, the connection wires of ordinary shock sensors are wrapped with shielded wires. The explosion sensor is an AC signal generator, but it is very different from most other AC signal generators in cars.
3. First of all, the shell and internal parts of the blast sensor are very fragile and are easily affected by factors such as vibration, temperature change and chemical corrosion, resulting in failure. Especially in high temperature, humidity and corrosion environments, the failure rate of the blast sensor will increase greatly. Secondly, the use environment of the car is also related to the life of the shock sensor.
4. The reasons for the engine explosion are as follows: the air-fuel ratio is incorrect. Too thinThe fuel-air mixing ratio will increase the combustion temperature, and the increase in the combustion temperature will cause the engine temperature to rise, which is of course easy to explode; the engine accumulates excessive carbon.
5. Unlike stators and magnetoresistors, they are usually piezoelectric components. They are made of special materials that can sense mechanical pressure or vibration (for example, when the engine starts to explode, it can generate AC voltage). Engine explosions caused by too early fire, poor exhaust gas recycling and poor-quality fuel will cause engine damage.
6. The cause of the failure of the detonation sensor. The phenomenon of the failure of the detonation sensor is that the engine does not have an obvious response, and the fuel consumption increases and the engine shakes slightly: when the engine is working, the ignition time is too early (ignition advance angle), the load, temperature and fuel quality of the engine will cause The motive explodes.
It is used to measure engine shake and adjust the ignition advance angle when the engine detonates. It is usually piezoelectric ceramics. When the engine vibrates, the ceramics inside are squeezed to produce electrical signals. Because this electrical signal is very weak, the connection wires of ordinary shock sensors are wrapped with shielded wires.
It is used to measure engine shake and adjust the ignition advance angle when the engine explodes; generally, it is piezoelectric ceramic, and when the engine vibrates, the ceramic inside will be pressed to generate an electrical signal. Because the electrical signal is relatively weak, the connection wire of the general shock sensor is covered by the shielded wire.
Explosive sensor is a piezoelectric sensor that can convert vibration into voltage. The detonation sensor is usually installed on the generator of a car to detect whether the engine may cause detonation, so as to adjust the ignition advance time through the electronic control system to avoid the occurrence of detonation.
1. The explosion sensor is an AC signal generator, butThey are very different from most other automotive AC signal generators. In addition to detecting the speed and position of the hinge like magnetoelectric crankshaft and camshaft position sensors, they also detect vibration or mechanical pressure. Unlike stators and magnetoresistors, they are usually piezoelectric devices.
2. It is used to measure engine jitter and adjust the ignition advance angle when the engine bursts. It is usually piezoelectric ceramics. When the engine vibrates, the ceramics inside are squeezed to produce electrical signals. Because this electrical signal is very weak, the connection wires of ordinary shock sensors are wrapped with shielded wires.
3. It is used to determine the vibration of the engine, and it is used to adjust the ignition advance angle when the engine explodes. There are many kinds of x0dx0a detonation sensors, among which the earliest application is the magneto-retractable detonation sensor, which is mainly composed of magnetic cores, permanent magnets and induction coils.
4. The function of the explosion sensor is to detect the vibration of the engine when the engine speed changes. The shock sensor will express the vibration of the engine in the form of voltage. In order to avoid explosion during ignition, the electronic control module will delay the ignition to avoid engine explosion. .
5. The detonation sensor has several functions of the detonation sensor. The function of the detonation sensor is: it is used to determine the jitter of the engine, and it is used to adjust the ignition advance angle when the engine produces an explosion; it is an AC signal generator to detect the speed and position of the hinge. Explosive sensors include: magnetic core, permanent magnet, induction coil.
6. The functions of the automobile detonation sensor are as follows: 1. Explosive sensor is a kind of AC signal generator, but it is very different from most other car AC signal generators.
HS code-based scenario planning for exports-APP, download it now, new users will receive a novice gift pack.
1. When the engine inhales the fuel steam and air mixture and enters the compression link, the spark plug will automatically explode before ignition, resulting in cylinder vibration, which is the explosion. This phenomenon is particularly common because fuel contains low-flammable substances.
2. It is usually piezoelectric ceramics. When the engine vibrates, the ceramics inside are squeezed to produce electrical signals. Because this electrical signal is very weak, the connection wires of ordinary shock sensors are wrapped with shielded wires. The explosion sensor is an AC signal generator, but it is very different from most other AC signal generators in cars.
3. First of all, the shell and internal parts of the blast sensor are very fragile and are easily affected by factors such as vibration, temperature change and chemical corrosion, resulting in failure. Especially in high temperature, humidity and corrosion environments, the failure rate of the blast sensor will increase greatly. Secondly, the use environment of the car is also related to the life of the shock sensor.
4. The reasons for the engine explosion are as follows: the air-fuel ratio is incorrect. Too thinThe fuel-air mixing ratio will increase the combustion temperature, and the increase in the combustion temperature will cause the engine temperature to rise, which is of course easy to explode; the engine accumulates excessive carbon.
5. Unlike stators and magnetoresistors, they are usually piezoelectric components. They are made of special materials that can sense mechanical pressure or vibration (for example, when the engine starts to explode, it can generate AC voltage). Engine explosions caused by too early fire, poor exhaust gas recycling and poor-quality fuel will cause engine damage.
6. The cause of the failure of the detonation sensor. The phenomenon of the failure of the detonation sensor is that the engine does not have an obvious response, and the fuel consumption increases and the engine shakes slightly: when the engine is working, the ignition time is too early (ignition advance angle), the load, temperature and fuel quality of the engine will cause The motive explodes.
It is used to measure engine shake and adjust the ignition advance angle when the engine detonates. It is usually piezoelectric ceramics. When the engine vibrates, the ceramics inside are squeezed to produce electrical signals. Because this electrical signal is very weak, the connection wires of ordinary shock sensors are wrapped with shielded wires.
It is used to measure engine shake and adjust the ignition advance angle when the engine explodes; generally, it is piezoelectric ceramic, and when the engine vibrates, the ceramic inside will be pressed to generate an electrical signal. Because the electrical signal is relatively weak, the connection wire of the general shock sensor is covered by the shielded wire.
Explosive sensor is a piezoelectric sensor that can convert vibration into voltage. The detonation sensor is usually installed on the generator of a car to detect whether the engine may cause detonation, so as to adjust the ignition advance time through the electronic control system to avoid the occurrence of detonation.
1. The explosion sensor is an AC signal generator, butThey are very different from most other automotive AC signal generators. In addition to detecting the speed and position of the hinge like magnetoelectric crankshaft and camshaft position sensors, they also detect vibration or mechanical pressure. Unlike stators and magnetoresistors, they are usually piezoelectric devices.
2. It is used to measure engine jitter and adjust the ignition advance angle when the engine bursts. It is usually piezoelectric ceramics. When the engine vibrates, the ceramics inside are squeezed to produce electrical signals. Because this electrical signal is very weak, the connection wires of ordinary shock sensors are wrapped with shielded wires.
3. It is used to determine the vibration of the engine, and it is used to adjust the ignition advance angle when the engine explodes. There are many kinds of x0dx0a detonation sensors, among which the earliest application is the magneto-retractable detonation sensor, which is mainly composed of magnetic cores, permanent magnets and induction coils.
4. The function of the explosion sensor is to detect the vibration of the engine when the engine speed changes. The shock sensor will express the vibration of the engine in the form of voltage. In order to avoid explosion during ignition, the electronic control module will delay the ignition to avoid engine explosion. .
5. The detonation sensor has several functions of the detonation sensor. The function of the detonation sensor is: it is used to determine the jitter of the engine, and it is used to adjust the ignition advance angle when the engine produces an explosion; it is an AC signal generator to detect the speed and position of the hinge. Explosive sensors include: magnetic core, permanent magnet, induction coil.
6. The functions of the automobile detonation sensor are as follows: 1. Explosive sensor is a kind of AC signal generator, but it is very different from most other car AC signal generators.
Furniture imports HS code analysis
author: 2024-12-23 23:47Best global trade intelligence tools
author: 2024-12-23 23:36HS code referencing for port authorities
author: 2024-12-23 23:11Refrigeration equipment HS code checks
author: 2024-12-23 21:32Trade data visualization dashboards
author: 2024-12-23 21:21Mineral ores HS code tariff details
author: 2024-12-23 22:50Global trade intelligence forums
author: 2024-12-23 22:42Comparative trade performance metrics
author: 2024-12-23 22:25Trade data for consumer electronics
author: 2024-12-23 21:24Advanced customs data integration
author: 2024-12-23 21:13147.59MB
Check591.65MB
Check428.81MB
Check921.86MB
Check138.93MB
Check246.75MB
Check914.57MB
Check556.77MB
Check224.51MB
Check688.29MB
Check191.76MB
Check179.48MB
Check883.38MB
Check972.61MB
Check261.63MB
Check752.59MB
Check133.69MB
Check118.18MB
Check274.75MB
Check737.87MB
Check592.92MB
Check468.19MB
Check448.88MB
Check589.49MB
Check954.39MB
Check585.41MB
Check342.15MB
Check892.47MB
Check713.65MB
Check856.19MB
Check326.92MB
Check417.31MB
Check373.43MB
Check693.13MB
Check636.46MB
Check923.73MB
CheckScan to install
HS code-based scenario planning for exports to discover more
Netizen comments More
2761 Sourcing opportunities filtered by HS code
2024-12-23 23:16 recommend
909 Trade data for pharmaceutical imports
2024-12-23 22:22 recommend
721 How to identify top importing countries
2024-12-23 22:19 recommend
825 Trade data integration with BI tools
2024-12-23 21:37 recommend
94 Global trade scenario planning
2024-12-23 21:21 recommend